--- title: PostProcess DEMI 910 slug: process/postprocess-demi-910 description: Enhance your 3D printing workflow with the PostProcess DEMI 910 washer, now validated for cleaning parts from M and L series Carbon printers. This comprehensive guide details operational procedures for washing parts made with Carbon resins. docTags: createdAt: 2025-02-10T23:39:55.638Z --- # Overview ::::VerticalSplit{layout="middle"} :::VerticalSplitItem ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/u0H_j9z9pJcrRa_kGNPbJ_image.png) ::: :::VerticalSplitItem The **PostProcess DEMI 910** enables the on-platform washing of parts made with M and L series Carbon printers. This guide will show the unique-to-Carbon operation of the DEMI 910. Refer to the operator's manual for general use instructions. ::: :::: ## Dimensions ::::VerticalSplit{layout="middle"} :::VerticalSplitItem **Access Panels Open ** ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/Dz0nJzVngYA7KJmqUDK8p_image.png) ::: :::VerticalSplitItem **Access Panels Closed** ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/rIAhfseut9EIC1aiuG7V5_image.png) ::: :::: :::hint{type="info"} Go to the [PostProcess DEMI 910 website](https://www.postprocess.com/demi910/) for: - user manual containing specific information on safety, site prep, installation, operation, maintenance, and troubleshooting - solvent SDS - PostProcess contact info ::: # Operation **Two M1/M2 platforms** **OR one L1 platform** can be placed in the washer at one time. :::hint{type="info"} M3 and M3 Max platforms are not currently compatible with DEMI 910 brackets. ::: ::::::WorkflowBlock :::::WorkflowBlockItem **Fixture adjustment** This applies to both **M Series** and **L1 brackets.** - Tilt fixture up and away from the solvent and slide sideways along the rail to the desired location. - Lower fixture down towards solvent. ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/PxhxJ0ks7uBSWMiKuYIv5_image.png) ::::VerticalSplit{layout="middle"} :::VerticalSplitItem - Make sure to seat the tab on the underside of the bracket arm into the **rectangular notches on the rail** to prevent sideways motion. ::: :::VerticalSplitItem ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/rYLCAUWgIeBugTOCQkUFA_rail-tabs01.jpg) ::: :::: **M Series Fixture Adjustment Video** ::embed[]{url="https://player.vimeo.com/video/556987242"} ::::: :::::WorkflowBlockItem **Mount the platform in the bracket** Place your platform in the M or L1 fixtures as shown below. :::hint{type="warning"} Do not submerge the mount of the M Series platform or allow solvent into the cavity on the underside of the L1 platform! ::: ::::VerticalSplit{layout="middle"} :::VerticalSplitItem **M Series platform** ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/5Y5SvKnukcwsOmZJDyL2v_m-platform-in-bracket01.jpg) ::: :::VerticalSplitItem **L1 platform** ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/feEA8jrFUKAy4ScIv2oib_l-platform-in-bracket01.jpg) ::: :::: ::::: :::::WorkflowBlockItem **Start the wash cycle** ::::VerticalSplit{layout="middle"} :::VerticalSplitItem Close the lid and start the wash cycle. ::: :::VerticalSplitItem ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/bXLMkMo2cUVVFsR94ec2D_image.png) ::: :::: ::::: :::WorkflowBlockItem **Rinse parts** 1. As soon as the wash is complete, remove the platform from the DEMI 910. 2. Post dunk the parts in **IPA **for** 10 vertical dunks** on platform to displace the solvent and let dry for at least **30 minutes** before curing or baking. ::: :::::: # Wash Settings Carbon has tested the **DEMI 910 **using the **PLM-450-SUB solvent **with the resins listed in the table below. Use the table to set the proper ultrasonics and wash time. :::hint{type="info"} Use the shortest effective wash cycle. Longer solvent exposure times may degrade material properties ::: | **Resin** | **% Ultrasonics** | **Time (start)\*** | **Time (maximum)\*\*** | | ----------------- | ----------------- | ------------------ | ---------------------- | | RPU 130 | 100 | 2 min | 6 min | | RPU 70 | 100 | 2 min | 6 min | | EPX 82 & EPX 86FR | 100 | 2 min | 4 min | | EPU 41 | 100 | 2 min | 6 min | | UMA 90 | 100 | 2 min | 6 min | | IND 405 | 100 | 2 min | 6 min | | MPU 100 | 100 | 2 min | 6 min | | DPR 10 | 100 | 2 min | 6 min | \* Recommended starting point. Parts may be washed for less time if sufficiently clean. \*\* Washing beyond the recommended maximum time could lead to degradation of material properties. :::hint{type="warning"} Carbon does not recommend washing SIL 30 with the DEMI 910. ::: :::hint{type="info"} PLM-450-SUB solvent is not compatible with the Carbon Smart Part Washer. ::: # Support For questions and support for the DEMI 910 Series hardware or software, please contact: ::::VerticalSplit{layout="middle"} :::VerticalSplitItem ![](https://api.archbee.com/api/optimize/3CesIL2dYMCHPZvRjp8S0/C2CLoIvX4pGBm2Lq4vTjt_image.png) ::: :::VerticalSplitItem **PostProcess Technologies** 2495 Main Street, Suite 615 Buffalo, NY 14214 USA +1 866 430 5354 support\@postprocess.com **PostProcess Technologies International** Les Aqueducs B3 535 Routes des Lucioles 06560 Sophia Antipolis, France +33 (0)4 22 32 68 13 ::: :::: For questions and support related to washing parts made with Carbon resins, please contact [support@carbon3d.com](mailto\:support@carbon3d.com).